Basic Command Summary

   &$  Extended Command Summary      I0   Product Information
   *$  Enhanced Command Summary      I1   Results of ROM Chksum
   A   Answer Incoming Call          I2   Link Report
   A/  Repeat Last Command           Ln   n=0-7,Speaker Volume
   A>  Continuously Repeat Command   M0   Speaker off
   B0  CCITT Answer Sequence         M1   Speaker On Until CD
   B1  Bell Answer Sequence          M2   Speaker Always On
   Dn  Dial a Phone Numbers          M3   Speaker Off during Dialing
       n=0...9*#TPR,;W@!( )-         O    Return On-Line State
   DL  Dial Last Number              P    Pulse Dialing
   DSn Dial Stored Phone Numbers     Q0   Return Result Codes
       n=0-6                         Q1   Quiet (No Result Codes)
   E0  Command Echo Disabled         Sr=n Set Register r to value n
   E1  Command Echo Enabled               n=0-255
   H0  Hang Up                       Sr?  Read contents of S Register r
   H1  Off Hook                      T    Tone Dialing
   V0  Numeric Result Codes
   V1  Verbose Result Codes
   X0  Basic Result Codes (0-4)
   X1  Result Codes (0-5, 10-21)
   X2  Result Codes (0-6, 10-21)
   X3  Result Codes (0-5, 7-21)
   X4  Result Codes (0-21)
   X5  Error Control Result Codes (0-21)
   X6  Error Control Result Codes (0-21)
   X7  Error Control Result Codes (0-21)
   Zn  n=0-3, Reset Modem And Load User Profile n
       n=4, Reset Modem And Load Factory Settings
   +++ Escape Sequence Code


   Extended Command Summary

   &B0  DTE Follow Linked DCE Rate   &K0  No Error Control
   &B1  Fixed DTE Rate               &K1  MNP4 (Include MNP3)
   &C0  CD Always On                 &K2  MNP4 + MNP5
   &C1  Track Presence of Carrier    &K3  V.42 + &K1
   &D0  Ignore DTR                   &K4  V.42 + V.42bis + &K2
   &D1  108.1
   &D2  DTR/108.2
   &D3  108.2 + Load profile 0
   &F   Load Factory settings        &L0  Dial Up Line
   &G0  No Guard Tone                &L1  2 Wire Leased Line
   &G1  Reserved                     &L2  4 Wire Leased Line
   &G2  1800 Hz Guard Tone           &M0  Asynchronous Data Format
   &H0  Flow Control Disabled        &M1  Async command, Sync Data
   &H2  Reserved                     &M2  DIRECT
   &H3  Hardware CTS/RTS             &M3  Synchronous
   &H4  Local XON/XOFF
   &H5  Reserved
   &J0  Single Phone Line
   &J1  Multiple phone line (A/A1)
   &N0  Multi-Auto                   &N24 Bell 212A 1200
   &N1  V.33 14400/12000             &N25 Bell 103 300
   &N2  V.33 12000                   &N32 FAX 14400/12000/9600/7200/4800/2400
   &N3  V.32 9600T/9600/7200T/4800   &N34 Reserved
   &N4  V.32 9600/7200T/4800         &N35 Reserved
   &N5  V.32 4800                    &N36 Reserved
   &N6  V.29 9600                    &P0  M/B Ratio = 39%/61%
   &N7  V.29 7200                    &P1  M/B Ratio = 33%/67%
   &N8  V.29 4800                    &R0  CTS Follows RTS
   &N9  V.27ter 4800                 &R1  Ignore RTS
   &N10 V.27ter 2400                 &S0  DSR Always On
   &N11 V.26bis 2400                 &S1  Data Set Ready
   &N12 V.23 1200                    &T0  Terminate Testing
   &N13 V.23 600                     &T1  Analog Loopback test
   &N14 V.22bis 2400/1200            &T3  Local Digital Loopback test
   &N15 V.22 1200                    &T4  Grant RDL Request
   &N16 V.21 300                     &T5  Deny RDL Request
   &N17 V.32b 14400/12000/7200       &T6  Initiate RDL
   &N18 V.32b 12000/7200             &T7  Initiate RDL with self test
   &N19 V.32b 7200                   &T8  Initiate ALB with self test
   &Vn  n=0, View Current Settings
        n=1-4, View User Profile n-1
        n=5, View Factory Settings
   &Wn  n=0-3, Save Current Settings To User Profile n
   &X0  Internal Clock
   &X1  External Clock
   &X2  Remote Clock
   &Y0  Destructive, Expedited
   &Y1  Nondestructive, Expedited
   &Y2  Nondestructive, Unexpedited
   &Zn=s  Store The Dial String s To EEPROM AT Location n (0-5)
   &Zn?   Display The Phone Numbers Stored In EEPROM At Location n


   Enhanced Command Summary

   *B0  Disabled Dial-Backup
   *Bn  n=1-6, Set Dial-Backup Phone Pointer at Location n-1
   *C0  10 Bit Character Length
   *C1  11 Bit Character Length
   *C2   9 Bit Character Length
   *C3   8 Bit Character Length
   *Dn  n=0-5, Set Default Dial Phone Pointer At Location n
   *E0  If Error Control Negotiation Fail, Keep Non-ErrorControl Connection
   *E1  If Not Error Control Linked, Disconnect The Line
   *F0  Deny Remote Configuration
   *F1  Accept Remote Configuration
   *G0  Disable Security function
   *G1  Enable Level 1 Security.(Password Check)
   *G2  Enable Level 2 Security.(Password Check and Call Back)
   *HS  Modify Supervisory Password
   *Hn  Modify User Password.(n=0-9)
   *I0  AT Command Set
   *I1  V.25 bis Command Set
   *M0  Leased Line Auto Handshake on Originate Mode
   *M1  Leased Line Auto Handshake On Answer Mode
   *Pn  n=0-15, Leased line Transmission Power Level
   *Q0  No Response To Poor Signal Quality
   *Q1  Retrain Action Taken If Signal Quality Is Poor
   *Q2  Adaptive Rate (Auto fall back or fall forward)
   *Q3  Disconnect
   *Rab Read Remote Configuration to Local Profile
        a=0-3, Local User Profile
        b=0-3, Remote User Profile
            4, Remote Current Configuration
            5, Remote Factory Default
   *V   View Password Table
   *Wab Write Local User Profile to Remote User Profile and
        Reset Remote Modem from that Profile