patch-1.3.22 linux/drivers/net/README.arcnet-jumpers
Next file: linux/drivers/net/README.modules
Previous file: linux/drivers/net/README.arcnet
Back to the patch index
Back to the overall index
- Lines: 1912
- Date:
Thu Jan 1 02:00:00 1970
- Orig file:
v1.3.21/linux/drivers/net/README.arcnet-jumpers
- Orig date:
Thu Jul 13 16:20:20 1995
diff -u --recursive --new-file v1.3.21/linux/drivers/net/README.arcnet-jumpers linux/drivers/net/README.arcnet-jumpers
@@ -1,1911 +0,0 @@
-
------------------------------------------------------------------------------
-This file is a supplement to README.arcnet. Please read that for general
-driver configuration help.
------------------------------------------------------------------------------
-
-Because so many people (myself included) seem to have obtained ARCnet cards
-without manuals, this will be a quick listing of all jumper settings I can
-find. Please e-mail apenwarr@foxnet.net with any settings for
-your particular card.
-
-Even if your ARCnet model isn't listed, but has the same jumpers, please
-e-mail me to say so.
-
-If your model isn't listed, and has different settings, PLEASE PLEASE tell
-me. I had to figure mine out without the manual, and it WASN'T FUN!
-
-Cards Listed in this file (in this order, mostly):
-
- Manufacturer Model # Bits
- ------------ ------- ----
- SMC PC100 8
- SMC PC110 8
- SMC PC120 8
- SMC PC130 8
- SMC PC270E 8
- SMC PC500 16
- SMC PC500Longboard 16
- SMC PC550Longboard 16
- SMC PC600 16
- SMC? LCS-8830-T 16?
- Puredata PDI507 16
- CNet Tech CN120-Series 8
- CNet Tech CN160-Series 16
- No Name -- 8/16
- No Name Taiwan R.O.C(?) 8
- Tiara Tiara Lancard(?)
-
-
-** SMC = Standard Microsystems Corp.
-** CNet Tech = CNet Technology, Inc.
-
-The model # is listed right above specifics for that card. Don't forget to
-read "quick briefing" first, since it applies to all ARCnets.
-
-
-Unclassified Stuff
-------------------
- - Please send any other information you can find.
-
- - And some unknowns (other info is welcome!):
- From: root@ultraworld.xs4all.nl (Timo Hilbrink)
- To: apenwarr@foxnet.net (Avery Pennarun)
- Date: Wed, 26 Oct 1994 02:10:32 +0000 (GMT)
- Reply-To: timoh@xs4all.nl
-
- [...parts deleted...]
-
- About the jumpers: On my PC130 there is one more jumper, located near the
- cable-connector and it's for changing to star or bus topology;
- closed: star - open: bus
- On the PC500 are some more jumper-pins, one block labled with RX,PDN,TXI
- and another with ALE,LA17,LA18,LA19 these are undocumented..
-
- [...more parts deleted...]
-
- --- CUT ---
-
-
-Quick Briefing:
----------------
-
-All ARCnet cards should have a total of four different settings:
-
- - the I/O address: this is the "port" your ARCnet card is on. Probed
- values, as of v0.14, are only from 0x200 through 0x3F0. (If your card
- has additional ones, which is possible, please tell me.) This should not
- be the same as any other device on your system. According to a doc I
- got from Novell, MS Windows prefers values of 0x300 or more, eating
- netconnections on my system otherwise.
- - Avery's favourite: 0x300.
-
- - the IRQ: on 8-bit cards, it might be 2 (9), 3, 4, 5, or 7.
- on 16-bit cards, it might be 2 (9), 3, 4, 5, 7, or 10-15. Make
- sure this is different from any other card on your system. Note that
- IRQ2 is the same as IRQ9, as far as Linux is concerned.
- - Avery's favourite: IRQ2.
-
- - the memory address: Unlike most cards, ARCnets use "shared memory" for
- copying buffers around. Make SURE it doesn't conflict with any other
- used memory in your system!
- A0000 - VGA graphics memory (ok if you don't have VGA)
- B0000 - Monochrome text mode
- C0000 \ One of these is your VGA BIOS - usually C0000.
- E0000 /
- F0000 - System BIOS
-
- Anything less than 0xA0000 is, well, a BAD idea since it isn't above
- 640k.
- - Avery's favourite: 0xD0000
-
- - the station address: Every ARCnet card has its own "unique" network
- address from 0 to 255. Unlike ethernet, you can set this address
- yourself. Since it's only 8 bits, you can only have 254 ARCnet cards on
- a network. DON'T use 0 or 255, since these are reserved. (although neat
- stuff will probably happen if you DO use them). By the way, if you
- haven't already guessed, don't set this the same as any other ARCnet on
- your network!
- - Avery's favourite: 3 and 4. Not that it matters.
-
-
-** Standard Microsystems Corp (SMC) **
-PC100, PC110, PC120, PC130 (8-bit cards)
-PC500, PC600 (16-bit cards)
----------------------------------
- - mainly from Avery Pennarun <apenwarr@foxnet.net>. Values depicted are
- from Avery's setup.
- - special thanks to Timo Hilbrink <timoh@xs4all.nl> for noting that PC120,
- 130, 500, and 600 all have the same switches as Avery's PC100.
- PC500/600 have several extra, undocumented pins though. (?)
- - PC110 settings were verified by Stephen A. Wood <saw@cebaf.gov>
- - On the other hand, John Edward Bauer <jbauer@badlands.NoDak.edu> said
- the PC110 settings are all wrong. In his case, you need to switch all
- the 1's with 0's. If you're having problems, try that.
- - Also, the JP- and S-numbers probably don't match your card exactly. Try
- to find jumpers/switches with the same number of settings - it's
- probably more reliable.
-
-
- JP5 [|] : : : :
-(IRQ Setting) IRQ2 IRQ3 IRQ4 IRQ5 IRQ7
- Put exactly one jumper on exactly one set of pins.
-
- 1 2 3 4 5 6 7 8 9 10
- S1 /----------------------------------\
-(I/O and Memory | 1 1 * 0 0 0 0 * 1 1 0 1 |
- addresses) \----------------------------------/
- |--| |--------| |--------|
- (a) (b) (m)
-
- a: The first digit of the I/O address.
- Setting Value
- ------- -----
- 00 0
- 01 1
- 10 2
- 11 3
-
- b: The second digit of the I/O address.
- Setting Value
- ------- -----
- 0000 0
- 0001 1
- 0010 2
- ... ...
- 1110 E
- 1111 F
-
- The I/O address is in the form ab0. For example, if
- a is 0x2 and b is 0xE, the address will be 0x2E0.
-
- DO NOT SET THIS LESS THAN 0x200!!!!!
-
-
- m: The first digit of the memory address.
- Setting Value
- ------- -----
- 0000 0
- 0001 1
- 0010 2
- ... ...
- 1110 E
- 1111 F
-
- The memory address is in the form m0000. For example, if
- m is D, the address will be 0xD0000.
-
- DO NOT SET THIS TO C0000, F0000, OR LESS THAN A0000!
-
- 1 2 3 4 5 6 7 8
- S2 /--------------------------\
-(Station Address) | 1 1 0 0 0 0 0 0 |
- \--------------------------/
-
- Setting Value
- ------- -----
- 00000000 00
- 10000000 01
- 01000000 02
- ...
- 01111111 FE
- 11111111 FF
-
- Note that this is binary with the digits reversed!
-
- DO NOT SET THIS TO 0 OR 255 (0xFF)!
-
-
-*****************************************************************************
-
-** Standard Microsystems Corp (SMC) **
-PC130E/PC270E (8-bit cards)
----------------------------
- - from Juergen Seifert <seifert@htwm.de>
-
-
-STANDARD MICROSYSTEMS CORPORATION (SMC) ARCNET(R)-PC130E/PC270E
-===============================================================
-
-This description has been written by Juergen Seifert <seifert@htwm.de>
-using information from the following Original SMC Manual
-
- "Configuration Guide for
- ARCNET(R)-PC130E/PC270
- Network Controller Boards
- Pub. # 900.044A
- June, 1989"
-
-ARCNET is a registered trademark of the Datapoint Corporation
-SMC is a registered trademark of the Standard Microsystems Corporation
-
-The PC130E is an enhanced version of the PC130 board, is equipped with a
-standard BNC female connector for connection to RG-62/U coax cable.
-Since this board is designed both for point-to-point connection in star
-networks and for connection to bus networks, it is downwardly compatible
-with all the other standard boards designed for coax networks (that is,
-the PC120, PC110 and PC100 star topology boards and the PC220, PC210 and
-PC200 bus topology boards).
-
-The PC270E is an enhanced version of the PC260 board, is equipped with two
-modular RJ11-type jacks for connection to twisted pair wiring.
-It can be used in a star or a daisy-chained network.
-
-
- 8 7 6 5 4 3 2 1
- ________________________________________________________________
- | | S1 | |
- | |_________________| |
- | Offs|Base |I/O Addr |
- | RAM Addr | ___|
- | ___ ___ CR3 |___|
- | | \/ | CR4 |___|
- | | PROM | ___|
- | | | N | | 8
- | | SOCKET | o | | 7
- | |________| d | | 6
- | ___________________ e | | 5
- | | | A | S | 4
- | |oo| EXT2 | | d | 2 | 3
- | |oo| EXT1 | SMC | d | | 2
- | |oo| ROM | 90C63 | r |___| 1
- | |oo| IRQ7 | | |o| _____|
- | |oo| IRQ5 | | |o| | J1 |
- | |oo| IRQ4 | | STAR |_____|
- | |oo| IRQ3 | | | J2 |
- | |oo| IRQ2 |___________________| |_____|
- |___ ______________|
- | |
- |_____________________________________________|
-
-Legend:
-
-SMC 90C63 ARCNET Controller / Transceiver /Logic
-S1 1-3: I/O Base Address Select
- 4-6: Memory Base Address Select
- 7-8: RAM Offset Select
-S2 1-8: Node ID Select
-EXT Extended Timeout Select
-ROM ROM Enable Select
-STAR Selected - Star Topology (PC130E only)
- Deselected - Bus Topology (PC130E only)
-CR3/CR4 Diagnostic LEDs
-J1 BNC RG62/U Connector (PC130E only)
-J1 6-position Telephone Jack (PC270E only)
-J2 6-position Telephone Jack (PC270E only)
-
-Setting one of the switches to Off/Open means "1", On/Closed means "0".
-
-
-Setting the Node ID
--------------------
-
-The eight switches in group S2 are used to set the node ID.
-Each node attached to the network must have an unique node ID which
-must be diffrent from 0.
-Switch 1 serves as the least significant bit (LSB).
-
-The node ID is the sum of the values of all switches set to "1"
-These values are:
- Switch | Value
- -------|-------
- 1 | 1
- 2 | 2
- 3 | 4
- 4 | 8
- 5 | 16
- 6 | 32
- 7 | 64
- 8 | 128
-
-Some Examples:
-
- Switch | Hex | Decimal
- 8 7 6 5 4 3 2 1 | Node ID | Node ID
- ----------------|---------|---------
- 0 0 0 0 0 0 0 0 | not allowed
- 0 0 0 0 0 0 0 1 | 1 | 1
- 0 0 0 0 0 0 1 0 | 2 | 2
- 0 0 0 0 0 0 1 1 | 3 | 3
- . . . | |
- 0 1 0 1 0 1 0 1 | 55 | 85
- . . . | |
- 1 0 1 0 1 0 1 0 | AA | 170
- . . . | |
- 1 1 1 1 1 1 0 1 | FD | 253
- 1 1 1 1 1 1 1 0 | FE | 254
- 1 1 1 1 1 1 1 1 | FF | 255
-
-
-Setting the I/O Base Address
-----------------------------
-
-The first three switches in switch group S1 are used to select one
-of eight possible I/O Base addresses using the followig table
-
-
- Switch | Hex I/O
- 1 2 3 | Address
- -------|--------
- 0 0 0 | 260
- 0 0 1 | 290
- 0 1 0 | 2E0 (Manufactor's default)
- 0 1 1 | 2F0
- 1 0 0 | 300
- 1 0 1 | 350
- 1 1 0 | 380
- 1 1 1 | 3E0
-
-
-Setting the Base Memory (RAM) buffer Address
---------------------------------------------
-
-The memory buffer requires 2K of a 16K block of RAM. The base of this
-16K block can be located in any of eight positions.
-Switches 4-6 of switch group S1 select the Base of the 16K block.
-Within that 16K address space, the buffer may be assigned any one of four
-positions, determined by the offset, switches 7 and 8 of group S1.
-
- Switch | Hex RAM | Hex ROM
- 4 5 6 7 8 | Address | Address *)
- -----------|---------|-----------
- 0 0 0 0 0 | C0000 | C2000
- 0 0 0 0 1 | C0800 | C2000
- 0 0 0 1 0 | C1000 | C2000
- 0 0 0 1 1 | C1800 | C2000
- | |
- 0 0 1 0 0 | C4000 | C6000
- 0 0 1 0 1 | C4800 | C6000
- 0 0 1 1 0 | C5000 | C6000
- 0 0 1 1 1 | C5800 | C6000
- | |
- 0 1 0 0 0 | CC000 | CE000
- 0 1 0 0 1 | CC800 | CE000
- 0 1 0 1 0 | CD000 | CE000
- 0 1 0 1 1 | CD800 | CE000
- | |
- 0 1 1 0 0 | D0000 | D2000 (Manufactor's default)
- 0 1 1 0 1 | D0800 | D2000
- 0 1 1 1 0 | D1000 | D2000
- 0 1 1 1 1 | D1800 | D2000
- | |
- 1 0 0 0 0 | D4000 | D6000
- 1 0 0 0 1 | D4800 | D6000
- 1 0 0 1 0 | D5000 | D6000
- 1 0 0 1 1 | D5800 | D6000
- | |
- 1 0 1 0 0 | D8000 | DA000
- 1 0 1 0 1 | D8800 | DA000
- 1 0 1 1 0 | D9000 | DA000
- 1 0 1 1 1 | D9800 | DA000
- | |
- 1 1 0 0 0 | DC000 | DE000
- 1 1 0 0 1 | DC800 | DE000
- 1 1 0 1 0 | DD000 | DE000
- 1 1 0 1 1 | DD800 | DE000
- | |
- 1 1 1 0 0 | E0000 | E2000
- 1 1 1 0 1 | E0800 | E2000
- 1 1 1 1 0 | E1000 | E2000
- 1 1 1 1 1 | E1800 | E2000
-
-*) To enable the 8K Boot PROM install the jumper ROM.
- The default is jumper ROM not installed.
-
-
-Setting the Timeouts and Interrupt
-----------------------------------
-
-The jumpers labeled EXT1 and EXT2 are used to determine the timeout
-parameters. These two jumpers are normally left open.
-Refer to the COM9026 Data Sheet for alternate configurations.
-
-To select a hardware interrupt level set one (only one!) of the jumpers
-IRQ2, IRQ3, IRQ4, IRQ5, IRQ7. The Manufactor's default is IRQ2.
-
-
-Configuring the PC130E for Star or Bus Topology
------------------------------------------------
-
-The single jumper labeled STAR is used to configure the PC130E board for
-star or bus topology.
-When the jumper is installed, the board may be used in a star network, when
-it is removed, the board can be used in a bus topology.
-
-
-Diagnostic LEDs
----------------
-
-Two diagnostic LEDs are visible on the rear bracket of the board.
-The green LED monitors the network activity: the red one shows the
-board activity:
-
- Green | Status Red | Status
- -------|------------------- ---------|-------------------
- on | normal activity flash/on | data transfer
- blink | reconfiguration off | no data transfer;
- off | defectiv board or | incorect memory or
- | node ID is zero | I/O address
-
-
-*****************************************************************************
-
-** Standard Microsystems Corp (SMC) **
-PC500/PC550 Long Board (16-bit cards)
--------------------------------------
- - from Juergen Seifert <seifert@htwm.de>
-
-
-STANDARD MICROSYSTEMS CORPORATION (SMC) ARCNET-PC500/PC550 Long Board
-=====================================================================
-
-Note: There is another Version of the PC500 called Short Version, which
- is different in hard- and software! The most important differences
- are:
- - The long board has no Shared memory
- - On the long board the selection of the interrupt is done by binary
- coded switch, on the short board directly by jumper.
-
-
-This description has been written by Juergen Seifert <seifert@htwm.de>
-using information from the following Original SMC Manual
-
- "Configuration Guide for
- SMC ARCNET-PC500/PC550
- Series Network Controller Boards
- Pub. # 900.033 Rev. A
- November, 1989"
-
-ARCNET is a registered trademark of the Datapoint Corporation
-SMC is a registered trademark of the Standard Microsystems Corporation
-
-The PC500 is equipped with a standard BNC female connector for connection
-to RG-62/U coax cable.
-The board is designed both for point-to-point connection in star networks
-and for connection to bus networks.
-
-The PC550 is equipped with two modular RJ11-type jacks for connection
-to twisted pair wiring.
-It can be used in a star or a daisy-chained network.
-
- 1
- 0 9 8 7 6 5 4 3 2 1 6 5 4 3 2 1
- ____________________________________________________________________
- < | SW1 | | SW2 | |
- > |_____________________| |_____________| |
- < IRQ |I/O Addr |
- > ___|
- < CR4 |___|
- > CR3 |___|
- < ___|
- > N | | 8
- < o | | 7
- > d | S | 6
- < e | W | 5
- > A | 3 | 4
- < d | | 3
- > d | | 2
- < r |___| 1
- > |o| _____|
- < |o| | J1 |
- > 3 1 JP6 |_____|
- < |o|o| JP2 | J2 |
- > |o|o| |_____|
- < 4 2__ ______________|
- > | | |
- <____| |_____________________________________________|
-
-Legend:
-
-SW1 1-6: I/O Base Address Select
- 7-10: Interrupt Select
-SW2 1-6: Reserved for Future Use
-SW3 1-8: Node ID Select
-JP2 1-4: Extended Timeout Select
-JP6 Selected - Star Topology (PC500 only)
- Deselected - Bus Topology (PC500 only)
-CR3 Green Monitors Network Activity
-CR4 Red Monitors Board Activity
-J1 BNC RG62/U Connector (PC500 only)
-J1 6-position Telephone Jack (PC550 only)
-J2 6-position Telephone Jack (PC550 only)
-
-Setting one of the switches to Off/Open means "1", On/Closed means "0".
-
-
-Setting the Node ID
--------------------
-
-The eight switches in group SW3 are used to set the node ID. Each node
-attached to the network must have an unique node ID which must be
-diffrent from 0.
-Switch 1 serves as the least significant bit (LSB).
-
-The node ID is the sum of the values of all switches set to "1"
-These values are:
-
- Switch | Value
- -------|-------
- 1 | 1
- 2 | 2
- 3 | 4
- 4 | 8
- 5 | 16
- 6 | 32
- 7 | 64
- 8 | 128
-
-Some Examples:
-
- Switch | Hex | Decimal
- 8 7 6 5 4 3 2 1 | Node ID | Node ID
- ----------------|---------|---------
- 0 0 0 0 0 0 0 0 | not allowed
- 0 0 0 0 0 0 0 1 | 1 | 1
- 0 0 0 0 0 0 1 0 | 2 | 2
- 0 0 0 0 0 0 1 1 | 3 | 3
- . . . | |
- 0 1 0 1 0 1 0 1 | 55 | 85
- . . . | |
- 1 0 1 0 1 0 1 0 | AA | 170
- . . . | |
- 1 1 1 1 1 1 0 1 | FD | 253
- 1 1 1 1 1 1 1 0 | FE | 254
- 1 1 1 1 1 1 1 1 | FF | 255
-
-
-Setting the I/O Base Address
-----------------------------
-
-The first six switches in switch group SW1 are used to select one
-of 32 possible I/O Base addresses using the followig table
-
- Switch | Hex I/O
- 6 5 4 3 2 1 | Address
- -------------|--------
- 0 1 0 0 0 0 | 200
- 0 1 0 0 0 1 | 210
- 0 1 0 0 1 0 | 220
- 0 1 0 0 1 1 | 230
- 0 1 0 1 0 0 | 240
- 0 1 0 1 0 1 | 250
- 0 1 0 1 1 0 | 260
- 0 1 0 1 1 1 | 270
- 0 1 1 0 0 0 | 280
- 0 1 1 0 0 1 | 290
- 0 1 1 0 1 0 | 2A0
- 0 1 1 0 1 1 | 2B0
- 0 1 1 1 0 0 | 2C0
- 0 1 1 1 0 1 | 2D0
- 0 1 1 1 1 0 | 2E0 (Manufactor's default)
- 0 1 1 1 1 1 | 2F0
- 1 1 0 0 0 0 | 300
- 1 1 0 0 0 1 | 310
- 1 1 0 0 1 0 | 320
- 1 1 0 0 1 1 | 330
- 1 1 0 1 0 0 | 340
- 1 1 0 1 0 1 | 350
- 1 1 0 1 1 0 | 360
- 1 1 0 1 1 1 | 370
- 1 1 1 0 0 0 | 380
- 1 1 1 0 0 1 | 390
- 1 1 1 0 1 0 | 3A0
- 1 1 1 0 1 1 | 3B0
- 1 1 1 1 0 0 | 3C0
- 1 1 1 1 0 1 | 3D0
- 1 1 1 1 1 0 | 3E0
- 1 1 1 1 1 1 | 3F0
-
-
-Setting the Interrupt
----------------------
-
-Switches seven through ten of switch group SW1 are used to select the
-interrupt level. The interrupt level is binary coded, so selections
-from 0 to 15 would be possible, but only the following eight values will
-be supported: 3, 4, 5, 7, 9, 10, 11, 12.
-
- Switch | IRQ
- 10 9 8 7 |
- ---------|--------
- 0 0 1 1 | 3
- 0 1 0 0 | 4
- 0 1 0 1 | 5
- 0 1 1 1 | 7
- 1 0 0 1 | 9 (=2) (default)
- 1 0 1 0 | 10
- 1 0 1 1 | 11
- 1 1 0 0 | 12
-
-
-Setting the Timeouts
---------------------
-
-The two jumpers JP2 (1-4) are used to determine the timeout parameters.
-These two jumpers are normally left open.
-Refer to the COM9026 Data Sheet for alternate configurations.
-
-
-Configuring the PC500 for Star or Bus Topology
-----------------------------------------------
-
-The single jumper labeled JP6 is used to configure the PC500 board for
-star or bus topology.
-When the jumper is installed, the board may be used in a star network, when
-it is removed, the board can be used in a bus topology.
-
-
-Diagnostic LEDs
----------------
-
-Two diagnostic LEDs are visible on the rear bracket of the board.
-The green LED monitors the network activity: the red one shows the
-board activity:
-
- Green | Status Red | Status
- -------|------------------- ---------|-------------------
- on | normal activity flash/on | data transfer
- blink | reconfiguration off | no data transfer;
- off | defectiv board or | incorect memory or
- | node ID is zero | I/O address
-
-
-*****************************************************************************
-
-** Possibly SMC **
-LCS-8830-T (16-bit card)
-------------------------
- - from Mathias Katzer <mkatzer@HRZ.Uni-Bielefeld.DE>
-
-This is a LCS-8830-T made by SMC, I think ('SMC' only appears on one PLCC,
-nowhere else, not even on the few xeroxed sheets from the manual).
-
-SMC Arcnet Board Type LCS-8830-T
-
- ------------------------------------
- | |
- | JP3 88 8 JP2 |
- | ##### | \ |
- | ##### ET1 ET2 ###|
- | 8 ###|
- | U3 SW 1 JP0 ###| Phone Jacks
- | -- ###|
- | | | |
- | | | SW2 |
- | | | |
- | | | ##### |
- | -- ##### #### BNC Connector
- | ####
- | 888888 JP1 |
- | 234567 |
- -- -------
- |||||||||||||||||||||||||||
- --------------------------
-
-
-SW1: DIP-Switches for Station Address
-SW2: DIP-Switches for Memory Base and I/O Base addresses
-
-JP0: If closed, internal termination on (default open)
-JP1: IRQ Jumpers
-JP2: Boot-ROM enabled if closed
-JP3: Jumpers for respsonse timeout
-
-U3: Boot-ROM Socket
-
-
-ET1 ET2 Response Time Idle Time Reconfiguration Time
-
- 78 86 840
- X 285 316 1680
- X 563 624 1680
- X X 1130 1237 1680
-
-(X means closed jumper)
-
-(DIP-Switch downwards means "0")
-
-The station address is binary-coded with SW1.
-
-The I/O base address is coded with DIP-Switches 6,7 and 8 of SW2:
-
-Switches Base
-678 Address
-000 260-26f
-100 290-29f
-010 2e0-2ef
-110 2f0-2ff
-001 300-30f
-101 350-35f
-011 380-38f
-111 3e0-3ef
-
-
-DIP Switches 1-5 of SW2 encode the RAM and ROM Adress Range:
-
-Switches Ram Rom
-12345 Adress Range Address Range
-00000 C:0000-C:07ff C:2000-C:3fff
-10000 C:0800-C:0fff
-01000 C:1000-C:17ff
-11000 C:1800-C:1fff
-00100 C:4000-C:47ff C:6000-C:7fff
-10100 C:4800-C:4fff
-01100 C:5000-C:57ff
-11100 C:5800-C:5fff
-00010 C:C000-C:C7ff C:E000-C:ffff
-10010 C:C800-C:Cfff
-01010 C:D000-C:D7ff
-11010 C:D800-C:Dfff
-00110 D:0000-D:07ff D:2000-D:3fff
-10110 D:0800-D:0fff
-01110 D:1000-D:17ff
-11110 D:1800-D:1fff
-00001 D:4000-D:47ff D:6000-D:7fff
-10001 D:4800-D:4fff
-01001 D:5000-D:57ff
-11001 D:5800-D:5fff
-00101 D:8000-D:87ff D:A000-D:bfff
-10101 D:8800-D:8fff
-01101 D:9000-D:97ff
-11101 D:9800-D:9fff
-00011 D:C000-D:c7ff D:E000-D:ffff
-10011 D:C800-D:cfff
-01011 D:D000-D:d7ff
-11011 D:D800-D:dfff
-00111 E:0000-E:07ff E:2000-E:3fff
-10111 E:0800-E:0fff
-01111 E:1000-E:17ff
-11111 E:1800-E:1fff
-
-
-*****************************************************************************
-
-** PureData Corp **
-PDI507 (16-bit card)
---------------------
- - from Mark Rejhon <mdrejhon@magi.com> (slight modifications by
- Avery)
- - Send questions/suggestions/etc about this text to Mark.
-
-Jumpers:
-
- There is a jumper array at the bottom of the card, near the edge
- connector. This array is labelled J1. They control the IRQs and
- something else. Put only one jumper on the IRQ pins.
-
- IRQ2 - Use IRQ 2 (same as IRQ 9 as far as software is concerned)
- IRQ3 - Use IRQ 3 (used by COM2 or COM4 serial port if either exists)
- IRQ4 - Use IRQ 4 (used by COM1 or COM3 serial port if either exists)
- IRQ5 - Use IRQ 5 (used by LPT2 parallel port if one exists)
- IRQ6 - Use IRQ 6 (used by Floppy Disk Controller if one exists)
- IRQ7 - Use IRQ 7 (used by LPT1 parallel port if one exists)
-
-[Avery's note: This "unknown" set of two jumpers appears to be on all
-ARCnet cards by SMC as well. Putting jumpers on them seems to affect the
-status register, but only for the two "reserved" bits, ETS1 and ETS2. Any
-further information is welcome.]
-
- ET1 - What is this? (Not tested, no jumper put on it)
- ET2 - What is this? (Not tested, no jumper put on it)
-
- There is a J2 jumper on two pins. A jumper should be put on them,
- since it was already there when I got the card. I don't know what
- this jumper is for though.
-
- There is a two-jumper array for J3. I don't know what it is for,
- but there were already two jumpers on it when I got the card. It's
- a six pin grid in a two-by-three fashion. The jumpers were
- configured as follows:
-
- .-------.
- o | o o |
- :-------: ------> Accessible end of card with connectors
- o | o o | in this direction ------->
- `-------'
-
- There is also a J4 jumper on two pins. A jumper should be put on
- them, since it was already there when I got the card. I don't know
- what this jumper is for though.
-
-
-DIP Switches:
-
- The dipswitches accessible on the accessible end of the card while
- it is installed, is used to set the arcnet address. There are 8
- switches. Use an address from 1 to 254.
-
- Switch No.
- 12345678 Arcnet address
- -----------------------------------------
- 00000000 FF (Don't use this!)
- 00000001 FE
- 00000010 FD
- ....
- 11111101 2
- 11111110 1
- 11111111 0 (Don't use this!)
-
- There is another dipswitch array of 8 switches at the top of the
- card. There are five labelled MS0-MS4 which seem to control the
- memory address, and another three labelled IO0-IO2 which seem to
- control the base I/O address of the card.
-
- This was difficult to test by trial and error, and the I/O addresses
- are in a weird order. This was tested by setting the DIP switches,
- rebooting the computer, and attempting to load ARCETHER at various
- addresses (mostly between 0x200 and 0x400). The address that caused
- the red transmit LED to blink, is the one that I thought works.
-
- Also, the address 0x3D0 seem to have a special meaning, since the
- ARCETHER packet driver loaded fine, but without the red LED
- blinking. I don't know what 0x3D0 is for though. I recommend using
- an address of 0x300 since Windows may not like addresses below
- 0x300.
-
- IO Switch No.
- 210 I/O address
- -------------------------------
- 111 0x260
- 110 0x290
- 101 0x2E0
- 100 0x2F0
- 011 0x300
- 010 0x350
- 001 0x380
- 000 0x3E0
-
- The memory switches set a reserved address space of 0x1000 bytes
- (0x100 segment units, or 4k). For example if I set an address of
- 0xD000, it will use up addresses 0xD000 to 0xD100.
-
- The memory switches were tested by booting using QEMM386 stealth,
- and using LOADHI to see what address automatically became excluded
- from the upper memory regions, and then attempting to load ARCETHER
- using these addresses.
-
- I recommend using an arcnet memory address of 0xD000, and putting
- the EMS page frame at 0xC000 while using QEMM stealth mode. That
- way, you get contiguous high memory from 0xD100 almost all the way
- the end of the megabyte.
-
- Memory Switch 0 (MS0) didn't seem to work properly when set to OFF
- on my card. It could be malfunctioning on my card. Experiment with
- it ON first, and if it doesn't work, set it to OFF. (It may be a
- modifier for the 0x200 bit?)
-
- MS Switch No.
- 43210 Memory address
- --------------------------------
- 00001 0xE100 (guessed - was not detected by QEMM)
- 00011 0xE000 (guessed - was not detected by QEMM)
- 00101 0xDD00
- 00111 0xDC00
- 01001 0xD900
- 01011 0xD800
- 01101 0xD500
- 01111 0xD400
- 10001 0xD100
- 10011 0xD000
- 10101 0xCD00
- 10111 0xCC00
- 11001 0xC900 (guessed - crashes tested system)
- 11011 0xC800 (guessed - crashes tested system)
- 11101 0xC500 (guessed - crashes tested system)
- 11111 0xC400 (guessed - crashes tested system)
-
-
-*****************************************************************************
-
-** CNet Technology Inc. **
-120 Series (8-bit cards)
-------------------------
- - from Juergen Seifert <seifert@htwm.de>
-
-
-CNET TECHNOLOGY INC. (CNet) ARCNET 120A SERIES
-==============================================
-
-This description has been written by Juergen Seifert <seifert@htwm.de>
-using information from the following Original CNet Manual
-
- "ARCNET
- USER'S MANUAL
- for
- CN120A
- CN120AB
- CN120TP
- CN120ST
- CN120SBT
- P/N:12-01-0007
- Revision 3.00"
-
-ARCNET is a registered trademark of the Datapoint Corporation
-
-P/N 120A ARCNET 8 bit XT/AT Star
-P/N 120AB ARCNET 8 bit XT/AT Bus
-P/N 120TP ARCNET 8 bit XT/AT Twisted Pair
-P/N 120ST ARCNET 8 bit XT/AT Star, Twisted Pair
-P/N 120SBT ARCNET 8 bit XT/AT Star, Bus, Twisted Pair
-
- __________________________________________________________________
- | |
- | ___|
- | LED |___|
- | ___|
- | N | | ID7
- | o | | ID6
- | d | S | ID5
- | e | W | ID4
- | ___________________ A | 2 | ID3
- | | | d | | ID2
- | | | 1 2 3 4 5 6 7 8 d | | ID1
- | | | _________________ r |___| ID0
- | | 90C65 || SW1 | ____|
- | JP 8 7 | ||_________________| | |
- | |o|o| JP1 | | | J2 |
- | |o|o| |oo| | | JP 1 1 1 | |
- | ______________ | | 0 1 2 |____|
- | | PROM | |___________________| |o|o|o| _____|
- | > SOCKET | JP 6 5 4 3 2 |o|o|o| | J1 |
- | |______________| |o|o|o|o|o| |o|o|o| |_____|
- |_____ |o|o|o|o|o| ______________|
- | |
- |_____________________________________________|
-
-Legend:
-
-90C65 ARCNET Probe
-S1 1-5: Base Memory Address Select
- 6-8: Base I/O Address Select
-S2 1-8: Node ID Select (ID0-ID7)
-JP1 ROM Enable Select
-JP2 IRQ2
-JP3 IRQ3
-JP4 IRQ4
-JP5 IRQ5
-JP6 IRQ7
-JP7/JP8 ET1, ET2 Timeout Parameters
-JP10/JP11 Coax / Twisted Pair Select (CN120ST/SBT only)
-JP12 Terminator Select (CN120AB/ST/SBT only)
-J1 BNC RG62/U Connector (all except CN120TP)
-J2 Two 6-position Telephone Jack (CN120TP/ST/SBT only)
-
-Setting one of the switches to Off means "1", On means "0".
-
-
-Setting the Node ID
--------------------
-
-The eight switches in SW2 are used to set the node ID. Each node attached
-to the network must have an unique node ID which must be diffrent from 0.
-Switch 1 (ID0) serves as the least significant bit (LSB).
-
-The node ID is the sum of the values of all switches set to "1"
-These values are:
-
- Switch | Label | Value
- -------|-------|-------
- 1 | ID0 | 1
- 2 | ID1 | 2
- 3 | ID2 | 4
- 4 | ID3 | 8
- 5 | ID4 | 16
- 6 | ID5 | 32
- 7 | ID6 | 64
- 8 | ID7 | 128
-
-Some Examples:
-
- Switch | Hex | Decimal
- 8 7 6 5 4 3 2 1 | Node ID | Node ID
- ----------------|---------|---------
- 0 0 0 0 0 0 0 0 | not allowed
- 0 0 0 0 0 0 0 1 | 1 | 1
- 0 0 0 0 0 0 1 0 | 2 | 2
- 0 0 0 0 0 0 1 1 | 3 | 3
- . . . | |
- 0 1 0 1 0 1 0 1 | 55 | 85
- . . . | |
- 1 0 1 0 1 0 1 0 | AA | 170
- . . . | |
- 1 1 1 1 1 1 0 1 | FD | 253
- 1 1 1 1 1 1 1 0 | FE | 254
- 1 1 1 1 1 1 1 1 | FF | 255
-
-
-Setting the I/O Base Address
-----------------------------
-
-The last three switches in switch block SW1 are used to select one
-of eight possible I/O Base addresses using the followig table
-
-
- Switch | Hex I/O
- 6 7 8 | Address
- ------------|--------
- ON ON ON | 260
- OFF ON ON | 290
- ON OFF ON | 2E0 (Manufactor's default)
- OFF OFF ON | 2F0
- ON ON OFF | 300
- OFF ON OFF | 350
- ON OFF OFF | 380
- OFF OFF OFF | 3E0
-
-
-Setting the Base Memory (RAM) buffer Address
---------------------------------------------
-
-The memory buffer (RAM) requires 2K. The base of this buffer can be
-located in any of eight positions. The address of the Boot Prom is
-memory base + 8K or memory base + 0x2000.
-Switches 1-5 of switch block SW1 select the Memory Base address.
-
- Switch | Hex RAM | Hex ROM
- 1 2 3 4 5 | Address | Address *)
- --------------------|---------|-----------
- ON ON ON ON ON | C0000 | C2000
- ON ON OFF ON ON | C4000 | C6000
- ON ON ON OFF ON | CC000 | CE000
- ON ON OFF OFF ON | D0000 | D2000 (Manufactor's default)
- ON ON ON ON OFF | D4000 | D6000
- ON ON OFF ON OFF | D8000 | DA000
- ON ON ON OFF OFF | DC000 | DE000
- ON ON OFF OFF OFF | E0000 | E2000
-
-*) To enable the Boot ROM install the jumper JP1
-
-Note: Since the switches 1 and 2 are always set to ON it may be possible
- that they can be used to add an offset of 2K, 4K or 6K to the base
- address, but this feature is not documented in the manual and I
- haven't testet it yet.
-
-
-Setting the Interrupt Line
---------------------------
-
-To select a hardware interrupt level install one (only one!) of the jumpers
-JP2, JP3, JP4, JP5, JP6. JP2 is the default.
-
- Jumper | IRQ
- -------|-----
- 2 | 2
- 3 | 3
- 4 | 4
- 5 | 5
- 6 | 7
-
-
-Setting the Internal Terminator on CN120AB/TP/SBT
---------------------------------------------------
-
-The jumper JP12 is used to enable the internal terminator.
-
- -----
- 0 | 0 |
- ----- ON | | ON
- | 0 | | 0 |
- | | OFF ----- OFF
- | 0 | 0
- -----
- Terminator Terminator
- disabled enabled
-
-
-Selecting the Connector Type on CN120ST/SBT
--------------------------------------------
-
- JP10 JP11 JP10 JP11
- ----- -----
- 0 0 | 0 | | 0 |
- ----- ----- | | | |
- | 0 | | 0 | | 0 | | 0 |
- | | | | ----- -----
- | 0 | | 0 | 0 0
- ----- -----
- Coaxial Cable Twisted Pair Cable
- (Default)
-
-
-Setting the Timeout Parameters
-------------------------------
-
-The jumpers labeled EXT1 and EXT2 are used to determine the timeout
-parameters. These two jumpers are normally left open.
-
-
-
-*****************************************************************************
-
-** CNet Technology Inc. **
-160 Series (16-bit cards)
--------------------------
- - from Juergen Seifert <seifert@htwm.de>
-
-CNET TECHNOLOGY INC. (CNet) ARCNET 160A SERIES
-==============================================
-
-This description has been written by Juergen Seifert <seifert@htwm.de>
-using information from the following Original CNet Manual
-
- "ARCNET
- USER'S MANUAL
- for
- CN160A
- CN160AB
- CN160TP
- P/N:12-01-0006
- Revision 3.00"
-
-ARCNET is a registered trademark of the Datapoint Corporation
-
-P/N 160A ARCNET 16 bit XT/AT Star
-P/N 160AB ARCNET 16 bit XT/AT Bus
-P/N 160TP ARCNET 16 bit XT/AT Twisted Pair
-
- ___________________________________________________________________
- < _________________________ ___|
- > |oo| JP2 | | LED |___|
- < |oo| JP1 | 9026 | LED |___|
- > |_________________________| ___|
- < N | | ID7
- > 1 o | | ID6
- < 1 2 3 4 5 6 7 8 9 0 d | S | ID5
- > _______________ _____________________ e | W | ID4
- < | PROM | | SW1 | A | 2 | ID3
- > > SOCKET | |_____________________| d | | ID2
- < |_______________| | IO-Base | MEM | d | | ID1
- > r |___| ID0
- < ____|
- > | |
- < | J1 |
- > | |
- < |____|
- > 1 1 1 1 |
- < 3 4 5 6 7 JP 8 9 0 1 2 3 |
- > |o|o|o|o|o| |o|o|o|o|o|o| |
- < |o|o|o|o|o| __ |o|o|o|o|o|o| ___________|
- > | | |
- <____________| |_______________________________________|
-
-Legend:
-
-9026 ARCNET Probe
-SW1 1-6: Base I/O Address Select
- 7-10: Base Memory Address Select
-SW2 1-8: Node ID Select (ID0-ID7)
-JP1/JP2 ET1, ET2 Timeout Parameters
-JP3-JP13 Interrupt Select
-J1 BNC RG62/U Connector (CN160A/AB only)
-J1 Two 6-position Telephone Jack (CN160TP only)
-LED
-
-Setting one of the switches to Off means "1", On means "0".
-
-
-Setting the Node ID
--------------------
-
-The eight switches in SW2 are used to set the node ID. Each node attached
-to the network must have an unique node ID which must be diffrent from 0.
-Switch 1 (ID0) serves as the least significant bit (LSB).
-
-The node ID is the sum of the values of all switches set to "1"
-These values are:
-
- Switch | Label | Value
- -------|-------|-------
- 1 | ID0 | 1
- 2 | ID1 | 2
- 3 | ID2 | 4
- 4 | ID3 | 8
- 5 | ID4 | 16
- 6 | ID5 | 32
- 7 | ID6 | 64
- 8 | ID7 | 128
-
-Some Examples:
-
- Switch | Hex | Decimal
- 8 7 6 5 4 3 2 1 | Node ID | Node ID
- ----------------|---------|---------
- 0 0 0 0 0 0 0 0 | not allowed
- 0 0 0 0 0 0 0 1 | 1 | 1
- 0 0 0 0 0 0 1 0 | 2 | 2
- 0 0 0 0 0 0 1 1 | 3 | 3
- . . . | |
- 0 1 0 1 0 1 0 1 | 55 | 85
- . . . | |
- 1 0 1 0 1 0 1 0 | AA | 170
- . . . | |
- 1 1 1 1 1 1 0 1 | FD | 253
- 1 1 1 1 1 1 1 0 | FE | 254
- 1 1 1 1 1 1 1 1 | FF | 255
-
-
-Setting the I/O Base Address
-----------------------------
-
-The first six switches in switch block SW1 are used to select the I/O Base
-address using the followig table:
-
- Switch | Hex I/O
- 1 2 3 4 5 6 | Address
- ------------------------|--------
- OFF ON ON OFF OFF ON | 260
- OFF ON OFF ON ON OFF | 290
- OFF ON OFF OFF OFF ON | 2E0 (Manufactor's default)
- OFF ON OFF OFF OFF OFF | 2F0
- OFF OFF ON ON ON ON | 300
- OFF OFF ON OFF ON OFF | 350
- OFF OFF OFF ON ON ON | 380
- OFF OFF OFF OFF OFF ON | 3E0
-
-Note: Other IO-Base addresses seem to be selectable, but only the above
- combinations are documented.
-
-
-Setting the Base Memory (RAM) buffer Address
---------------------------------------------
-
-The switches 7-10 of switch block SW1 are used to select the Memory
-Base address of the RAM (2K) and the PROM.
-
- Switch | Hex RAM | Hex ROM
- 7 8 9 10 | Address | Address
- ----------------|---------|-----------
- OFF OFF ON ON | C0000 | C8000
- OFF OFF ON OFF | D0000 | D8000 (Default)
- OFF OFF OFF ON | E0000 | E8000
-
-Note: Other MEM-Base addresses seem to be selectable, but only the above
- combinations are documented.
-
-
-Setting the Interrupt Line
---------------------------
-
-To select a hardware interrupt level install one (only one!) of the jumpers
-JP3 through JP13 using the following table:
-
- Jumper | IRQ
- -------|-----------------
- 3 | 14
- 4 | 15
- 5 | 12
- 6 | 11
- 7 | 10
- 8 | 3
- 9 | 4
- 10 | 5
- 11 | 6
- 12 | 7
- 13 | 2 (=9) Default!
-
-Note: - Do not use JP11=IRQ6, it may conflict with your Floppy Disk
- Controler
- - Use JP3=IRQ14 only, if you don't have an IDE-, MFM-, or RLL-
- Hard Disk, it may conflict with their controlers
-
-
-Setting the Timeout Parameters
-------------------------------
-
-The jumpers labeled JP1 and JP2 are used to determine the timeout
-parameters. These two jumpers are normally left open.
-
-
-*****************************************************************************
-
-** No Name **
-8-bit cards, 16-bit cards
--------------------------
- - from Juergen Seifert <seifert@htwm.de>
-
-NONAME 8-BIT ARCNET
-===================
-
-I have named this ARCnet card "NONAME", since there is no name of any
-manufactor on the Installation manual nor on the shipping box. The only
-hint to the existence of a manufactor at all is written into cupper,
-it is "Made in Taiwan"
-
-This description has been written by Juergen Seifert <seifert@htwm.de>
-using information from the Original
- "ARCnet Installation Manual"
-
-
- ________________________________________________________________
- | |STAR| BUS| T/P| |
- | |____|____|____| |
- | _____________________ |
- | | | |
- | | | |
- | | | |
- | | SMC | |
- | | | |
- | | COM90C65 | |
- | | | |
- | | | |
- | |__________-__________| |
- | _____|
- | _______________ | CN |
- | | PROM | |_____|
- | > SOCKET | |
- | |_______________| 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 |
- | _______________ _______________ |
- | |o|o|o|o|o|o|o|o| | SW1 || SW2 ||
- | |o|o|o|o|o|o|o|o| |_______________||_______________||
- |___ 2 3 4 5 7 E E R Node ID IOB__|__MEM____|
- | \ IRQ / T T O |
- |__________________1_2_M______________________|
-
-Legend:
-
-COM90C65: Arcnet Probe
-S1 1-8: Node ID Select
-S2 1-3: I/O Base Address Select
- 4-6: Memory Base Address Select
- 7-8: RAM Offset Select
-ET1, ET2 Extended Timeout Select
-ROM ROM Enable Select
-CN RG62 Coax Connector
-STAR| BUS | T/P Three fields for placing a sign (colored circle)
- indicating the topologie of the card
-
-Setting one of the switches to Off means "1", On means "0".
-
-
-Setting the Node ID
--------------------
-
-The eight switches in group SW1 are used to set the node ID.
-Each node attached to the network must have an unique node ID which
-must be diffrent from 0.
-Switch 8 serves as the least significant bit (LSB).
-
-The node ID is the sum of the values of all switches set to "1"
-These values are:
-
- Switch | Value
- -------|-------
- 8 | 1
- 7 | 2
- 6 | 4
- 5 | 8
- 4 | 16
- 3 | 32
- 2 | 64
- 1 | 128
-
-Some Examples:
-
- Switch | Hex | Decimal
- 1 2 3 4 5 6 7 8 | Node ID | Node ID
- ----------------|---------|---------
- 0 0 0 0 0 0 0 0 | not allowed
- 0 0 0 0 0 0 0 1 | 1 | 1
- 0 0 0 0 0 0 1 0 | 2 | 2
- 0 0 0 0 0 0 1 1 | 3 | 3
- . . . | |
- 0 1 0 1 0 1 0 1 | 55 | 85
- . . . | |
- 1 0 1 0 1 0 1 0 | AA | 170
- . . . | |
- 1 1 1 1 1 1 0 1 | FD | 253
- 1 1 1 1 1 1 1 0 | FE | 254
- 1 1 1 1 1 1 1 1 | FF | 255
-
-
-Setting the I/O Base Address
-----------------------------
-
-The first three switches in switch group SW2 are used to select one
-of eight possible I/O Base addresses using the followig table
-
- Switch | Hex I/O
- 1 2 3 | Address
- ------------|--------
- ON ON ON | 260
- ON ON OFF | 290
- ON OFF ON | 2E0 (Manufactor's default)
- ON OFF OFF | 2F0
- OFF ON ON | 300
- OFF ON OFF | 350
- OFF OFF ON | 380
- OFF OFF OFF | 3E0
-
-
-Setting the Base Memory (RAM) buffer Address
---------------------------------------------
-
-The memory buffer requires 2K of a 16K block of RAM. The base of this
-16K block can be located in any of eight positions.
-Switches 4-6 of switch group SW2 select the Base of the 16K block.
-Within that 16K address space, the buffer may be assigned any one of four
-positions, determined by the offset, switches 7 and 8 of group SW2.
-
- Switch | Hex RAM | Hex ROM
- 4 5 6 7 8 | Address | Address *)
- -----------|---------|-----------
- 0 0 0 0 0 | C0000 | C2000
- 0 0 0 0 1 | C0800 | C2000
- 0 0 0 1 0 | C1000 | C2000
- 0 0 0 1 1 | C1800 | C2000
- | |
- 0 0 1 0 0 | C4000 | C6000
- 0 0 1 0 1 | C4800 | C6000
- 0 0 1 1 0 | C5000 | C6000
- 0 0 1 1 1 | C5800 | C6000
- | |
- 0 1 0 0 0 | CC000 | CE000
- 0 1 0 0 1 | CC800 | CE000
- 0 1 0 1 0 | CD000 | CE000
- 0 1 0 1 1 | CD800 | CE000
- | |
- 0 1 1 0 0 | D0000 | D2000 (Manufactor's default)
- 0 1 1 0 1 | D0800 | D2000
- 0 1 1 1 0 | D1000 | D2000
- 0 1 1 1 1 | D1800 | D2000
- | |
- 1 0 0 0 0 | D4000 | D6000
- 1 0 0 0 1 | D4800 | D6000
- 1 0 0 1 0 | D5000 | D6000
- 1 0 0 1 1 | D5800 | D6000
- | |
- 1 0 1 0 0 | D8000 | DA000
- 1 0 1 0 1 | D8800 | DA000
- 1 0 1 1 0 | D9000 | DA000
- 1 0 1 1 1 | D9800 | DA000
- | |
- 1 1 0 0 0 | DC000 | DE000
- 1 1 0 0 1 | DC800 | DE000
- 1 1 0 1 0 | DD000 | DE000
- 1 1 0 1 1 | DD800 | DE000
- | |
- 1 1 1 0 0 | E0000 | E2000
- 1 1 1 0 1 | E0800 | E2000
- 1 1 1 1 0 | E1000 | E2000
- 1 1 1 1 1 | E1800 | E2000
-
-*) To enable the 8K Boot PROM install the jumper ROM.
- The default is jumper ROM not installed.
-
-
-Setting Interrupt Request Lines (IRQ)
--------------------------------------
-
-To select a hardware interrupt level set one (only one!) of the jumpers
-IRQ2, IRQ3, IRQ4, IRQ5 or IRQ7. The Manufactor's default is IRQ2.
-
-
-Setting the Timeouts
---------------------
-
-The two jumpers labeled ET1 and ET2 are used to determine the timeout
-parameters (respons and reconfiguration time). Every node in a network
-must be set to the same timeout values.
-
- ET1 ET2 | Response Time (us) | Reconfiguration Time (ms)
- --------|--------------------|--------------------------
- Off Off | 78 | 840 (Default)
- Off On | 285 | 1680
- On Off | 563 | 1680
- On On | 1130 | 1680
-
-On means jumper installed, Off means jumper not installed
-
-
-NONAME 16-BIT ARCNET
-====================
-
-The manual of my 8-Bit NONAME ARCnet Card contains another description
-of a 16-Bit Coax / Twisted Pair Card. This description is incomplete,
-because there are missing two pages in the manual booklet. (The table
-of contents reports pages ... 2-9, 2-11, 2-12, 3-1, ... but inside
-the booklet there is a diffrent way of counting ... 2-9, 2-10, A-1,
-(empty page), 3-1, ..., 3-18, A-1 (again), A-2)
-Also the picture of the board layout is not as good as the picture of
-8-Bit card, because there isn't any letter like "SW1" written to the
-picture.
-Should somebody have such a board, please feel free to complete this
-description or to send a mail to me!
-
-This description has been written by Juergen Seifert <seifert@htwm.de>
-using information from the Original
- "ARCnet Installation Manual"
-
-
- ___________________________________________________________________
- < _________________ _________________ |
- > | SW? || SW? | |
- < |_________________||_________________| |
- > ____________________ |
- < | | |
- > | | |
- < | | |
- > | | |
- < | | |
- > | | |
- < | | |
- > |____________________| |
- < ____|
- > ____________________ | |
- < | | | J1 |
- > | < | |
- < |____________________| ? ? ? ? ? ? |____|
- > |o|o|o|o|o|o| |
- < |o|o|o|o|o|o| |
- > |
- < __ ___________|
- > | | |
- <____________| |_______________________________________|
-
-
-Setting one of the switches to Off means "1", On means "0".
-
-
-Setting the Node ID
--------------------
-
-The eight switches in group SW2 are used to set the node ID.
-Each node attached to the network must have an unique node ID which
-must be diffrent from 0.
-Switch 8 serves as the least significant bit (LSB).
-
-The node ID is the sum of the values of all switches set to "1"
-These values are:
-
- Switch | Value
- -------|-------
- 8 | 1
- 7 | 2
- 6 | 4
- 5 | 8
- 4 | 16
- 3 | 32
- 2 | 64
- 1 | 128
-
-Some Examples:
-
- Switch | Hex | Decimal
- 1 2 3 4 5 6 7 8 | Node ID | Node ID
- ----------------|---------|---------
- 0 0 0 0 0 0 0 0 | not allowed
- 0 0 0 0 0 0 0 1 | 1 | 1
- 0 0 0 0 0 0 1 0 | 2 | 2
- 0 0 0 0 0 0 1 1 | 3 | 3
- . . . | |
- 0 1 0 1 0 1 0 1 | 55 | 85
- . . . | |
- 1 0 1 0 1 0 1 0 | AA | 170
- . . . | |
- 1 1 1 1 1 1 0 1 | FD | 253
- 1 1 1 1 1 1 1 0 | FE | 254
- 1 1 1 1 1 1 1 1 | FF | 255
-
-
-Setting the I/O Base Address
-----------------------------
-
-The first three switches in switch group SW1 are used to select one
-of eight possible I/O Base addresses using the followig table
-
- Switch | Hex I/O
- 3 2 1 | Address
- ------------|--------
- ON ON ON | 260
- ON ON OFF | 290
- ON OFF ON | 2E0 (Manufactor's default)
- ON OFF OFF | 2F0
- OFF ON ON | 300
- OFF ON OFF | 350
- OFF OFF ON | 380
- OFF OFF OFF | 3E0
-
-
-Setting the Base Memory (RAM) buffer Address
---------------------------------------------
-
-The memory buffer requires 2K of a 16K block of RAM. The base of this
-16K block can be located in any of eight positions.
-Switches 6-8 of switch group SW1 select the Base of the 16K block.
-Within that 16K address space, the buffer may be assigned any one of four
-positions, determined by the offset, switches 4 and 5 of group SW1.
-
- Switch | Hex RAM | Hex ROM
- 8 7 6 5 4 | Address | Address
- -----------|---------|-----------
- 0 0 0 0 0 | C0000 | C2000
- 0 0 0 0 1 | C0800 | C2000
- 0 0 0 1 0 | C1000 | C2000
- 0 0 0 1 1 | C1800 | C2000
- | |
- 0 0 1 0 0 | C4000 | C6000
- 0 0 1 0 1 | C4800 | C6000
- 0 0 1 1 0 | C5000 | C6000
- 0 0 1 1 1 | C5800 | C6000
- | |
- 0 1 0 0 0 | CC000 | CE000
- 0 1 0 0 1 | CC800 | CE000
- 0 1 0 1 0 | CD000 | CE000
- 0 1 0 1 1 | CD800 | CE000
- | |
- 0 1 1 0 0 | D0000 | D2000 (Manufactor's default)
- 0 1 1 0 1 | D0800 | D2000
- 0 1 1 1 0 | D1000 | D2000
- 0 1 1 1 1 | D1800 | D2000
- | |
- 1 0 0 0 0 | D4000 | D6000
- 1 0 0 0 1 | D4800 | D6000
- 1 0 0 1 0 | D5000 | D6000
- 1 0 0 1 1 | D5800 | D6000
- | |
- 1 0 1 0 0 | D8000 | DA000
- 1 0 1 0 1 | D8800 | DA000
- 1 0 1 1 0 | D9000 | DA000
- 1 0 1 1 1 | D9800 | DA000
- | |
- 1 1 0 0 0 | DC000 | DE000
- 1 1 0 0 1 | DC800 | DE000
- 1 1 0 1 0 | DD000 | DE000
- 1 1 0 1 1 | DD800 | DE000
- | |
- 1 1 1 0 0 | E0000 | E2000
- 1 1 1 0 1 | E0800 | E2000
- 1 1 1 1 0 | E1000 | E2000
- 1 1 1 1 1 | E1800 | E2000
-
-
-Setting Interrupt Request Lines (IRQ)
--------------------------------------
-
-??????????????????????????????????????
-
-
-Setting the Timeouts
---------------------
-
-??????????????????????????????????????
-
-
-*****************************************************************************
-
-** No Name **
-8-bit cards ("Made in Taiwan R.O.C.")
------------
- - from Vojtech Pavlik <vpav4328@diana.troja.mff.cuni.cz>
-
-I have named this ARCnet card "NONAME", since I got only the card with
-no manual at all and the only text identifying the manufacturer is
-"MADE IN TAIWAN R.O.C" printed on the card.
-
-This description was written by Vojtech Pavlik
-(vpav4328@diana.troja.mff.cuni.cz) using parts of the ARCNET-jumpers
-README file from Linux kernel 1.2.2.
-
- ____________________________________________________________
- | 1 2 3 4 5 6 7 8 |
- | |o|o| JP1 o|o|o|o|o|o|o|o| ON |
- | + o|o|o|o|o|o|o|o| ___|
- | _____________ o|o|o|o|o|o|o|o| OFF _____ | | ID7
- | | | SW1 | | | | ID6
- | > RAM (2k) | ____________________ | H | | S | ID5
- | |_____________| | || y | | W | ID4
- | | || b | | 2 | ID3
- | | || r | | | ID2
- | | || i | | | ID1
- | | 90C65 || d | |___| ID0
- | SW3 | || | |
- | |o|o|o|o|o|o|o|o| ON | || I | |
- | |o|o|o|o|o|o|o|o| | || C | |
- | |o|o|o|o|o|o|o|o| OFF |____________________|| | _____|
- | 1 2 3 4 5 6 7 8 | | | |___
- | ______________ | | | BNC |___|
- | | | |_____| |_____|
- | > EPROM SOCKET | |
- | |______________| |
- | ______________|
- | |
- |_____________________________________________|
-
-Legend:
-
-90C65 ARCNET Chip
-SW1 1-5: Base Memory Address Select
- 6-8: Base I/O Address Select
-SW2 1-8: Node ID Select (ID0-ID7)
-SW3 1-5: IRQ Select
- 6-7: Extra Timeout
- 8 : Rom Enable
-JP1 Led connector
-BNC Coax connector
-
-Although the jumpers SW1 and SW3 are marked SW, not JP, they are jumpers, not
-switches.
-
-Setting the jumpers to ON means connecting the upper two pins, off the bottom
-two - or - in case of IRQ setting, connecting none of them at all.
-
-Setting the Node ID
--------------------
-
-The eight switches in SW2 are used to set the node ID. Each node attached
-to the network must have an unique node ID which must be diffrent from 0.
-Switch 1 (ID0) serves as the least significant bit (LSB).
-
-Setting one of the switches to Off means "1", On means "0".
-
-The node ID is the sum of the values of all switches set to "1"
-These values are:
-
- Switch | Label | Value
- -------|-------|-------
- 1 | ID0 | 1
- 2 | ID1 | 2
- 3 | ID2 | 4
- 4 | ID3 | 8
- 5 | ID4 | 16
- 6 | ID5 | 32
- 7 | ID6 | 64
- 8 | ID7 | 128
-
-Some Examples:
-
- Switch | Hex | Decimal
- 8 7 6 5 4 3 2 1 | Node ID | Node ID
- ----------------|---------|---------
- 0 0 0 0 0 0 0 0 | not allowed
- 0 0 0 0 0 0 0 1 | 1 | 1
- 0 0 0 0 0 0 1 0 | 2 | 2
- 0 0 0 0 0 0 1 1 | 3 | 3
- . . . | |
- 0 1 0 1 0 1 0 1 | 55 | 85
- . . . | |
- 1 0 1 0 1 0 1 0 | AA | 170
- . . . | |
- 1 1 1 1 1 1 0 1 | FD | 253
- 1 1 1 1 1 1 1 0 | FE | 254
- 1 1 1 1 1 1 1 1 | FF | 255
-
-
-Setting the I/O Base Address
-----------------------------
-
-The last three switches in switch block SW1 are used to select one
-of eight possible I/O Base addresses using the followig table
-
-
- Switch | Hex I/O
- 6 7 8 | Address
- ------------|--------
- ON ON ON | 260
- OFF ON ON | 290
- ON OFF ON | 2E0 (Manufactor's default)
- OFF OFF ON | 2F0
- ON ON OFF | 300
- OFF ON OFF | 350
- ON OFF OFF | 380
- OFF OFF OFF | 3E0
-
-
-Setting the Base Memory (RAM) buffer Address
---------------------------------------------
-
-The memory buffer (RAM) requires 2K. The base of this buffer can be
-located in any of eight positions. The address of the Boot Prom is
-memory base + 0x2000.
-Jumpers 3-5 of jumper block SW1 select the Memory Base address.
-
- Switch | Hex RAM | Hex ROM
- 1 2 3 4 5 | Address | Address *)
- --------------------|---------|-----------
- ON ON ON ON ON | C0000 | C2000
- ON ON OFF ON ON | C4000 | C6000
- ON ON ON OFF ON | CC000 | CE000
- ON ON OFF OFF ON | D0000 | D2000 (Manufactor's default)
- ON ON ON ON OFF | D4000 | D6000
- ON ON OFF ON OFF | D8000 | DA000
- ON ON ON OFF OFF | DC000 | DE000
- ON ON OFF OFF OFF | E0000 | E2000
-
-*) To enable the Boot ROM set the jumper 8 of jumper block SW3 to position ON.
-
-The jumpers 1 and 2 probably add 0x0800, 0x1000 and 0x1800 to RAM addres.
-
-Setting the Interrupt Line
---------------------------
-
-Jumpers 1-5 of the jumper block SW3 controll the IRQ level.
-
- Jumper | IRQ
- 1 2 3 4 5 |
- ----------------------------
- ON OFF OFF OFF OFF | 2
- OFF ON OFF OFF OFF | 3
- OFF OFF ON OFF OFF | 4
- OFF OFF OFF ON OFF | 5
- OFF OFF OFF OFF ON | 7
-
-
-Setting the Timeout Parameters
-------------------------------
-
-The jumpers 6-7 of the jumper block SW3 are used to determine the timeout
-parameters. These two jumpers are normally left in the OFF position.
-
-
-*****************************************************************************
-** Tiara **
-(model unknown)
--------------------------
- - from Christoph Lameter <clameter@netcom.com>
-
-
-Here is information about my card as far as I could figure it out:
------------------------------------------------ tiara
-Tiara LanCard of Tiara Computer Systems.
-
-+----------------------------------------------+
-! ! Transmitter Unit ! !
-! +------------------+ -------
-! MEM Coax Connector
-! ROM 7654321 <- I/O -------
-! : : +--------+ !
-! : : ! 90C66LJ! +++
-! : : ! ! !D Switch to set
-! : : ! ! !I the Nodenumber
-! : : +--------+ !P
-! !++
-! 234567 <- IRQ !
-+------------!!!!!!!!!!!!!!!!!!!!!!!!--------+
- !!!!!!!!!!!!!!!!!!!!!!!!
-
-0 = Jumper Installed
-1 = Open
-
-Top Jumper line Bit 7 = Rom Enable 654=Memory location 321=I/O
-
-Settings for Memory Location (Top Jumper Line)
-456 Address selected
-000 C0000
-001 C4000
-010 CC000
-011 D0000
-100 D4000
-101 D8000
-110 DC000
-111 E0000
-
-Settings for I/O Address (Top Jumper Line)
-123 Port
-000 260
-001 290
-010 2E0
-011 2F0
-100 300
-101 350
-110 380
-111 3E0
-
-Settings for IRQ Selection (Lower Jumper Line)
-234567
-011111 IRQ 2
-101111 IRQ 3
-110111 IRQ 4
-111011 IRQ 5
-111110 IRQ 7
-
-*****************************************************************************
-
-
-Other Cards
------------
-
-I have no information on other models of ARCnet cards at the moment. Please
-send any and all info to:
- apenwarr@foxnet.net
-
-Thanks.
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov
with Sam's (original) version of this